Hotels & Resorts
Guestroom baths, suite vanities, and full property programs.
Hospitality & Multi-Residential
Built for projects, not just rooms.
Custom mirrors for hotels, restaurants, spas, and multi-family developments — specified to project requirements, manufactured in Europe, and delivered ready to install.
Custom
by default. Every piece is configurable — sizing, finish, lighting, mounting — to project spec.
Belgian glass
Low-iron, true-colour, no green cast. Easier to keep clean across a whole property.
One lead
From first email to final install. Direct line, one account, one set of drawings.
Capabilities
Built for the way projects work.
From single-property boutiques to multi-property developments — we work directly with design teams, owners, and contractors. Custom sizing, contract-grade lighting, and RAL-coded finishes are standard, not upcharge.
Custom SizingCertified to North American StandardsContract-grade LEDRAL-Coded FramesAnti-FogBelgian Low-Iron GlassDrawings on RequestTearsheets on Request
Contact us for a quotation →
Belgian low-iron · 4mmThe Glass
The glass is the mirror. We don't compromise it.
Every Claris piece is built on 4mm Belgian low-iron glass — the same substrate used in fine optics and museum vitrines. It reads neutral instead of green, holds true colour under any light, and resists the haze that builds on standard float over years of service.
-
True colour
Low-iron content removes the green cast common to standard float glass. Skin tones, finishes, and millwork read accurately — important in guestroom baths where lighting changes through the day.
-
Easier to maintain
A neutral, optically clean surface shows fewer streaks and water-spots than tinted or coated alternatives. Housekeeping routines shorten across the property.
-
Anti-fog standard
Heating pad bonded to the back panel. The mirror stays clear during showers — no daily manual wiping in wet zones.
-
Built to age slowly
Sealed edges and a certified driver assembly. The mirror is one of the few items in the room that doesn't need to be rotated out on a refresh cycle.
Where We Work
Every kind of room.
From boutique guestrooms to multi-family developments, we build mirrors to the spec of the room — single sculptural pieces or repeat programs.
Boutique & Lifestyle
Sculptural lobby pieces and signature design moments.
Restaurants & Bars
Powder rooms, back-bars, and statement pieces for the room.
Spa & Wellness
Wet-rated, anti-fog backlit panels for treatment rooms and wet zones.
Multi-Family Residential
Repeat programs for developments. One drawing, every unit.
From 11" × 18" to 96" × 48"Customization
Made to your spec, not ours.
Every piece in the catalog is a starting point. Sizes, finishes, light temperature, mounting, and even branded etchings are configurable at no additional engineering charge — because contract work requires it.
-
Sizing
Width, height, and depth to the millimeter. No restocking fee on custom dimensions.
-
Finishes
RAL-coded frame colours, brushed and polished metal options, custom glass tints.
-
Lighting
3000K Warm through 5000K Daylight. CCT-switchable, dimmable, motion-sensor.
-
Branding
Acid-etched logos, custom shapes, and property-specific glass treatments.
-
Glass
Anti-fog, anti-microbial, fire-rated, tempered, or laminated as required.
Keyhole mounting · recessed plugInstallation
Easy Installation
Every Claris mirror ships factory pre-wired with keyhole hangers on the back panel and a short plug that mates to a recessed wall outlet. Once outlet has been installed no electrician required for installation.
01
Pre-wired at the factory
Drivers, transformers, dimmer modules, and sensor logic are assembled and tested before shipment. Replace the unit, not the wall.
02
Keyhole mounting
Two keyhole hangers laser-cut into the back panel. The shop drawing gives the contractor exact stud and screw locations — one person can hang an 80" piece, no proprietary cleat hardware required.
03
Recessed wall plug
A short factory tail mates to a recessed plug installed by the electrician at the position we mark on the drawing — hidden behind the mirror. Certified to North American Standards. No visible cord, no surface conduit.
How We Work
Four steps.
No surprises.
From the first email to the last installed piece, you work with one project lead — the same person, the same number, through every stage.
01
Specify
Send drawings, mood boards, or rough dimensions. We work from whatever you have, and translate it into manufacturing-ready specs.
02
Sample
Glass and finish samples shipped on request. RAL chips, frame profiles, and full-scale mockups available before order.
03
Quote
A detailed quotation — unit pricing, freight, and tariffs in one document — returned after specs are signed off.
04
Deliver
European manufacturing, palletized to the project address. White-glove unboxing and on-site QA available in North America.
The Hospitality Program
Built around your project.
Dedicated support for hospitality projects of every scale. One account lead, one set of specifications, one timeline — from concept through installation and after-care.
Dedicated Lead
A single point of contact through every phase. Direct line, no portals.
Custom Specs
Sizing, finishes, light temperature, and wiring tailored to property standards.
Full Tearsheets
CAD, BIM, Revit blocks, and spec sheets ready for design and procurement teams.
Project Logistics
Coordinated delivery, on-site QA, replacement programs for multi-property rollouts.
Contact
Working on something? Tell us where, when, and how many.
Pricing and material samples are all project-specific. Email info@clariscompany.com or call +1 855.999.2124. We typically reply within four business hours.